Fox Factory Holding Corp. The Float X2 is Fox's big-hit air damper, designed from the ground-up for the enduro/gravity crowd.
The Fox Float DPX2 and the Fox Float X2 are some of the more popular shocks you can buy. Considering it comes stock on a lot of the bikes we carry, I was fairly comfortable with it from the beginning. Improperly installed shocks can fail, causing the rider to lose control, resulting in SERIOUS INJURY OR DEATH.The red “spacer limiter” present in select size FLOAT X2 shocks is a required component that limits the maximum quantity of volume spacers and must not be removed. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. The recommended settings in this tuning guide are designed to be a starting point, in order to get you out on your first ride in as few steps as possible. Factory Series products feature slippery smooth, ultra-durable Genuine Kashima Coat.Learn how to quickly set sag, air spring pressure, compression adjustments, rebound adjust, additional tuning options and more.The recommended settings in this tuning guide are designed to be a starting point, in order to get you out on your first ride in as few steps as possible.To best maintain the performance and durability of your product under normal use, FOX recommends that you have regular fork and shock maintenance performed according to the service intervals.Fox Factory Inc. uses cookies to improve your browsing experience on our website. I was able to push harder, land farther out and recover from deep compressions better. Fox Float x2 Dämpfer einstellen - Ähnliche Themen erledigt Dämpfer Fox Float DPS, 190x50mm, EVOL Air Preis: 95 € VB. One thing I could tell right away on my SB5.5 was that I needed to add some volume spacers to the shock as the mid and ending stroke did not have much support. I weigh 205 lbs dressed and have to take the shock to 300 PSI to get down to 32% static sag.
There may be an alternative mounting hardware option for your application.NOTE: Pressure measured at an ambient temperature of 70-75ËF.
You could add some HSC to help with this but I would prefer volume spacers to get air ramp up vs. more dampening. Use this number on the Help page at After setting shock air pressure by adjusting sag, use your air pressure in the table below to help find the suggested starting damper settings.
The 2021 FOX FLOAT X2 has an entirely new chassis, home to a new damping system and a new high-flow piston.
FOX products should be installed by a qualified bicycle service technician, in accordance with FOX installation specifications. In-line with the new Variable Valve Control (VVC) damper adjustment on the FOX 36, 38 and 40 Factory forks, the X2 now features the same … DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Once I got a feel for the low-speed rebound, I did the same for high-speed rebound. Coming apart without any tools and having the same seal kit that has been used from Fox for years, this is a home mechanics dream.
Then I adjust rebound. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. However the X2 is not this way, it takes some tools from Fox to get the air can seal off and once you take the shock apart you will have to also bleed and service the damper, a much more complicated procedure. After riding the bike, I looked into the leverage ratio and found that it supported my feeling. The award-winning, gravity-defying air shock is totally redesigned for 2021. To best maintain the performance and durability of your product under normal use, FOX recommends that you have regular fork and shock maintenance performed according to the service intervals listed below.WARNING: Never attempt to pull apart, open, disassemble, or service a FOX shock that is in a "stuck down" condition. They are both top of the line when it comes to Both shocks are also able to be fine-tuned with volume spacers to get the exact ramp up you want. Fox Factory Service Aktuelle Werkstattauslastung Exzellenter Kundenservice ist für uns eine Selbstverständlichkeit. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it.
From compression to rebound, I want the bike to feel balanced. Adding too much HSC can sometimes feel like the shock is getting “choked” off or not having a smooth stroke on a fast sharp compression. Contact FOX or an Authorized Service Center for repair.To best maintain the performance and durability of your product under normal use, FOX recommends that you have regular fork and shock maintenance performed according to the service intervals listed below.For general information and installation instructions click WARNING: Rear shock setup and configuration varies greatly between different bicycle manufacturers. For comparison purposes, the SB5.5 was the best choice considering it can be run with both DPX2 and Float X2 shocks.Once you have the X2 on a bike you immediately can feel a difference. 2021 FLOAT X2 F-S K HSC LSC HSR LSR FOX AM 250-75 CL RM Rezi CM Orange Neutral Logo
DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.WARNING: Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH.